How to Wash a Warhammer Printed Hoody Without Fading
By Warhammer Officially Licensed Merchandise | Published: 2026-10-15
Category: Conseils et entretien
Keep your Warhammer hoody print sharp with a cold, inside-out wash and air dry. Follow these steps to stop cracking and fading on officially licensed designs.
Quick answer
Wash your Warhammer printed hoody inside out in cold water on a gentle cycle, then air dry it flat or hang it. Skip the tumble dryer and iron entirely. This routine protects the digitally printed design from cracking and fading, and it works for any officially licensed hoody, including the Flesh Tearers Graffiti Insignia Hoodie.
Why the print fades (and what actually damages it)
Heat, friction, and harsh chemicals are the three main enemies of a digitally printed hoody. Hot water and tumble drying break down the bond between the ink and the fabric, which shows up as cracking or a washed-out look. Detergent residue and fabric softener can also leave a dull film over the design. Knowing this helps you see why each step below matters.
What you need before you start
You do not need special products. A mild liquid detergent, cold water, and a drying rack cover it. Avoid bleach, fabric softener, and dryer sheets. If your hoody has a care label, read it first; the Flesh Tearers Graffiti Insignia Hoodie label, for example, specifies machine wash cold, inside out, and no tumble dry, bleach, or iron.
How often should you wash it?
Wash only when needed. Spot-clean small marks between wears, and air the hoody overnight to freshen it. Overwashing is the most common reason prints fade early. For regular wear, every three to five wears is a sensible rhythm unless it is visibly soiled or sweaty.
Step-by-step washing routine
- Turn the hoody inside out: Close any zips and fasten buttons or drawcords so they do not rub against the print during the cycle. This simple flip is the single biggest protector of the design. Checkpoint: the printed side should face inward before it goes near the machine.
- Use cold water and a gentle cycle: Set your machine to cold (30°C or lower) and a delicate or hand-wash cycle. Add a mild liquid detergent, not powder, which can leave residue. Never add bleach or fabric softener. Mistake to avoid: assuming a quick warm wash is fine. Warm water speeds up fading.
- Wash with similar colours and fabrics: Wash your hoody with other dark or colour-fast items, not with towels or items that have zips, hooks, or rough textures. Those can snag the print. Checkpoint: separate rough items from your printed hoody load.
- Skip the tumble dryer: After washing, gently reshape the hoody and either lay it flat on a drying rack or hang it away from direct sunlight. Heat from a dryer is the fastest way to crack a print. Mistake to avoid: putting it on a radiator or in direct sun. Both cause fading.
- Store folded, not hung: Once dry, fold your hoody and store it in a drawer or on a shelf. Hanging a heavy hoody on a hanger can stretch the shoulders and distort the print over time. Next step: if it needs a refresh between washes, air it outside in the shade for an hour.
Product facts that guide care
- Warhammer 40,000: Flesh Tearers Graffiti Insignia Hoodie: 80% Ringspun cotton, 20% Polyester, 280gsm. This blend is soft but can pill or shrink with high heat, so cold washing and air drying keep the fit and surface smooth.
- Warhammer 40,000: Flesh Tearers Graffiti Insignia Hoodie: Machine wash cold, with like colours. Machine wash inside out. Do not bleach. Do not dry clean. Do not tumble dry. Do not iron. Following these exact instructions prevents ink cracking, colour bleed, and accidental heat damage to the print.
- Premium Salamanders 'Sons of Vulkan' T Shirt: Premium tees are a slightly different fit; order one size bigger than usual. If you size up for a relaxed fit, remember that a looser hoody still needs the same gentle wash routine to protect the print.
